CF 500, CF 600 Transmission - Automatic Transaxle/Transmission - 5R110 - Diagnostic Trouble Code Index
Diagnostic Trouble Code Index
Some of the following DTC code symptoms may experience multiple DTC code symptoms. The loss of one or more gears could be experienced depending on transmission condition.
Diagnostic Trouble Code Chart
Flash Code
DTC
Compo- nent
Descrip- tion
Condition
Symptom
Action
111
-
-
No codes found
-
-
-
113
P0706
TR-P Sensor
TR-P sensor frequency fault detected.
TR-P sensor signal frequency is out of normal range.
Only REVERSE, NEUTRAL and 5th gear detected. Engine may not crank.
GO to Pinpoint Test C.
114
P0707
TR-P Sensor
TR-P sensor circuit duty cycle low input.
TR-P sensor signal duty cycle is below threshold, sensor/circuit electrical malfunction.
Only REVERSE, NEUTRAL and 5th gear detected. Engine may not crank.
GO to Pinpoint Test C.
115
P0708
TR-P Sensor
TR-P sensor circuit duty cycle high input.
TR-P sensor signal duty cycle is above threshold, sensor/circuit electrical malfunction.
Only REVERSE, NEUTRAL and 5th gear detected. Engine may not crank.
GO to Pinpoint Test C.
412
P1702
TR-P Sensor
TR-P error.
TR-P sensor error detected.
Only REVERSE, NEUTRAL and 5th gear detected. Engine may not crank.
GO to Pinpoint Test C.
413
P1705
TR-P Sensor
TR-P sensor not in P or N positions during KOEO or KOER.
KOEO or KOER not run in P or N positions, or TR-P sensor circuit failure.
DTC is set.
RERUN KOEO and KOER in P or N position. GO to Pinpoint Test C.
122
P0711
TFT Sensor
No change if TFT during operation.
TCM has detected no TFT change during operation. TFT value stuck at some normal reading.
No 5th or 6th gears.
GO to Pinpoint Test B.
123, 121
P0712, P0710
TFT Sensor
157°C (315°F) indicated, TFT sensor circuit grounded.
Voltage drop across TFT sensor exceeds scale set for temperature of 157°C (315°F).
No 5th or 6th gears.
GO to Pinpoint Test B.
124, 121
P0713, P0710
TFT Sensor
-40°C (-40°F) indicated, TFT sensor circuit open.
Voltage drop across TFT sensor exceeds scale set for temperature of -40°C (-40°F).
No 5th or 6th gears.
GO to Pinpoint Test B.
414
P1711
TFT Sensor
TFT out of range during on-board diagnos- tics.
Transmission not operating at temperature during on-board diagnostics.
DTC set: engine cold or overheated.
Warm or cool engine to normal operating temperature. GO to Pinpoint Test B.
423
P1783
TFT Sensor
Trans- mission overtemp condition indicated.
Transmission fluid temperature exceeded 127°C (270°F).
Torque converter engages earlier than expected.
GO to Pinpoint Test B.
125
P0715
TSS Sensor
Insuff- icient input from TSS.
TCM detected a loss of TSS signal during operation.
Harsh shifts and engagements, engine rpm higher or lower than expected. No 1st, 3rd or 5th gear.
GO to Pinpoint Test D.
131
P0717
TSS Sensor
No TSS signal.
TCM has not detected a TSS signal.
Harsh shifts and engagements, engine rpm higher or lower than expected. No 1st, 3rd or 5th gear.
GO to Pinpoint Test D.
132
P0718
TSS Sensor
TSS signal noisy.
TCM has detected a noisy TSS signal.
-
GO to Pinpoint Test D.
133
P0720
OSS Sensor
Insuff- icient input from OSS.
TCM detected a loss of OSS signal during operation.
No 1st, 2nd, 3rd, 4th or 6th gear.
GO to Pinpoint Test D.
134
P0721
OSS Sensor
OSS signal noisy.
TCM has detected a noisy OSS signal.
-
GO to Pinpoint Test D.
135
P0722
OSS Sensor
No OSS signal.
TCM has detected no OSS signal.
No 1st, 2nd, 3rd, 4th or 6th gear.
GO to Pinpoint Test D.
435
U0100
TCM CAN
TCM communi-cation link error.
CAN link error detected by TCM. Loss of communication with the ECM.
Only reverse, neutral and 5th gears are available.
Refer to the Powertrain Control/ Emissions Diagnosis (PC/ED) manual.
141
P0730
Clutch Control Solenoid or Internal Parts
Gear ratio error.
TCM has detected a gear ratio error. OWC clutch or clutches may have failed.
Incorrect gear selection depending on failure or mode and manual lever position. Shift errors may also be due to other internal transmission concerns (stuck valves, damaged friction material). Engine rpm could be higher or lower than expected. May flash TCIL.
REFER to PID P0730_Status Chart, found immediately after Output State Control (OSC) Mode in this section, for a specific failure. REFER to the Solenoid Application charts located at the beginning of Pinpoint Tests - OSC Equipped Vehicles. If other solenoid DTCs are present, GO to Pinpoint Test A. If only P0730 is present, INSTALL the appropriate clutch solenoid. CLEAR DTCs, road test. If the concern is still present, REPAIR/INSTALL new internal transmission components.
142
P0740 (Output circuit check, generated only by electronical symptoms.)
TCC Solenoid
TCC solenoid open circuit failure.
TCC solenoid circuit fails to provide voltage drop across solenoid. Circuit open.
Open circuit: TCC never engages.
GO to Pinpoint Test A.
143
P0741
TCC Solenoid
TCC solenoid circuit perform- ance error.
Torque converter slippage detected during engagement command indicating a concern with mechanical or hydraulic operation of the converter clutch.
No TCC engagement.
Refer to Diagnosis By Symptom.
144
P0742
TCC Solenoid
TCC solenoid circuit shorted to ground.
TCC solenoid circuit fails to provide voltage drop across solenoid. Shorted to ground.
Short circuit: Only 5th gear at low vehicle speeds.
GO to Pinpoint Test A.
145
P0743
TCC Solenoid
TCC solenoid circuit failure.
TCC solenoid circuit fails to provide voltage drop across solenoid. Circuit open, shorted or TCM driver failure during on-board diagnostics.
Open circuit: TCC never engages.
Short circuit: Only 5th gear at lower speeds.
GO to Pinpoint Test A.
151
P0744
TCC Solenoid
TCC solenoid circuit shorted to power.
TCC solenoid circuit fails to provide voltage drop across solenoid. Circuit shorted to power.
No torque converter engagement.
GO to Pinpoint Test A.
421
P1744
TCC Solenoid
TCC solenoid circuit perform- ance error.
Torque converter slippage detected during engagement command indicating a concern with mechanical or hydraulic operation of the converter clutch.
No TCC engagement.
Refer to Diagnosis By Symptom.
152
P0748
b
PC-A Line Pressure Control Solenoid
PC-A solenoid circuit failure.
Voltage through PC-A solenoid is checked. An error will be noted if tolerance is exceeded.
Open circuit: maximum PC-A pressure, harsh engagements and shifts. Engine rpm higher than expected.
Only 5th gear present.
Short circuit: Maximum PC-A pressure, harsh engagements and shifts. Engine rpm higher than expected.
GO to Pinpoint Test E.
314
P0960
b
PC-A Line Pressure Control Solenoid
PC-A solenoid circuit open failure.
Voltage through PC-A solenoid is checked. An error will be noted if tolerance is exceeded.
Open circuit: maximum PC-A pressure, harsh engagements and shifts. Engine rpm higher than expected.
GO to Pinpoint Test E.
315
P0962
b
PC-A Line Pressure Control Solenoid
PC-A solenoid short to ground circuit failure.
Voltage through PC-A solenoid is checked. An error will be noted if tolerance is exceeded.
Short circuit: Only 5th gear present.
GO to Pinpoint Test E.
321
P0963
PC-A Line Pressure Control Solenoid
PC-A solenoid short to power circuit failure.
Voltage through PC-A solenoid is checked. An error will be noted if tolerance is exceeded.
Maximum PC-A pressure, harsh engagements and shifts. Engine rpm higher than expected.
GO to Pinpoint Test E.
153
P0750
a
SSPC-A Coast Clutch
SSPC-A solenoid circuit open.
SSPC-A circuit failed to provide voltage drop across solenoid. Circuit open or TCM driver failure during on-board diagnostics.
No 2nd, 4th or 6th gear.
GO to Pinpoint Test A.
154
P0751
SSPC-A Coast Clutch
SSPC-A circuit, clutch or solenoid failure - OFF.
SSPC-A circuit, clutch or solenoid failed in the OFF position during operation resulting in HIGH pressure in the hydraulic circuit.
Tow/Haul OFF:
-
No 1st, 3rd or 5th gears available.
Tow/Haul ON:
-
No 1st, 3rd or 5th gears available.
GO to Pinpoint Test A.
155
P0752
SSPC-A Coast Clutch
SSPC-A circuit, clutch or solenoid failure - ON.
SSPC-A circuit, clutch or solenoid failed in the ON position during operation resulting in LOW pressure in the hydraulic circuit.
Tow/Haul OFF:
-
No 1st, 2nd, 3rd or 5th gears available.
Tow/Haul ON:
-
No 2nd, 4th or 6th gears available.
GO to Pinpoint Test A.
211
P0753
a
SSPC-A Coast Clutch
SSPC-A solenoid circuit failure.
SSPC-A circuit failed to provide voltage drop across solenoid. Circuit failure or TCM driver failure.
Tow/Haul OFF:
-
No 2nd, 4th, 5th or 6th gears available.
-
No gears available.
Tow/Haul ON:
-
No 1st, 2nd, 3rd, 4th or 6th gears available.
GO to Pinpoint Test A.
323
P0973
SSPC-A Coast Clutch
SSPC-A solenoid or circuit shorted to ground.
Voltage through SSPC-A solenoid circuit is checked. An error will be noted if tolerance is exceeded. Short to ground failure detected.
Tow/Haul OFF:
-
No 2nd, 4th, 5th or 6th gears available.
Tow/Haul ON:
-
No 1st, 2nd, 3rd, 4th or 6th gears available.
GO to Pinpoint Test A.
324
P0974
SSPC-A Coast Clutch
SSPC-A solenoid or circuit shorted to power.
Voltage through SSPC-A solenoid circuit is checked. An error will be noted if tolerance is exceeded. Short to power failure detected.
Tow/Haul OFF:
-
No gears available.
Tow/Haul ON:
-
No 2nd, 4th or 6th gears available.
GO to Pinpoint Test A.
212
P0755
a
SSPC-B Overdrive Clutch
SSPC-B solenoid circuit open.
SSPC-B circuit, clutch or solenoid failed to provide voltage drop across solenoid. Circuit open or TCM driver failure during on-board diagnostics.
Tow/Haul OFF:
-
Only 1st or 3rd gears available.
Tow/Haul ON:
-
Only 5th gear available.
GO to Pinpoint Test A.
213
P0756
SSPC-B Overdrive Clutch
SSPC-B circuit, clutch or solenoid - OFF.
SSPC-B circuit, clutch or solenoid failed in the OFF position during operation resulting in LOW pressure in the hydraulic circuit.
Tow/Haul OFF:
-
No 2nd gear available.
Tow/Haul ON:
-
No 2nd, 4th or 6th gears available.
GO to Pinpoint Test A.
214
P0757
SSPC-B Overdrive Clutch
SSPC-B circuit, clutch or solenoid failure - ON.
SSPC-B circuit, clutch or solenoid failed in the ON position during operation resulting in HIGH pressure in the hydraulic circuit.
No 1st, 3rd or 5th gears available.
GO to Pinpoint Test A.
215
P0758
a
SSPC-B Overdrive Clutch
SSPC-B solenoid circuit failure.
SSPC-B circuit failed to provide voltage drop across solenoid. Circuit failure or TCM driver failure.
Tow/Haul OFF:
-
Only 1st or 3rd gears available.
-
No 2nd gear available.
Tow/Haul ON:
-
No 5th gear available.
-
Only 4th, 5th and 6th gears available.
GO to Pinpoint Test A.
331
P0976
SSPC-B Overdrive Clutch
SSPC-B solenoid or circuit shorted to ground.
Voltage through SSPC-B solenoid circuit is checked. An error will be noted if tolerance is exceeded. Short to ground failure detected.
Tow/Haul OFF:
-
No 2nd gear available.
Tow/Haul ON:
-
Only 4th and 6th gears available.
GO to Pinpoint Test A.
332
P0977
b
SSPC-B Overdrive Clutch
SSPC-B solenoid or circuit shorted to power.
Voltage through SSPC-B solenoid circuit is checked. An error will be noted if tolerance is exceeded. Short to power failure detected.
Tow/Haul OFF:
-
Only 1st and 3rd gears available.
Tow/Haul ON:
-
Only 5th gear available.
GO to Pinpoint Test A.
221
P0760
a
SSPC-C Intermed- iate Clutch
SSPC-C solenoid circuit open.
SSPC-C circuit failed to provide voltage drop across solenoid. Circuit open or TCM drive failure during on-board diagnostics.
Tow/Haul OFF:
-
Only 1st and 2nd gears available.
Tow/Haul ON:
-
Only 5th gear available.
GO to Pinpoint Test A.
222
P0761
SSPC-C Intermed- iate Clutch
SSPC-C circuit, clutch or solenoid failure - OFF.
SSPC-C circuit, clutch or solenoid failed in the OFF position during operation resulting in LOW pressure in the hydraulic circuit.
No 3rd and 4th gear available.
GO to Pinpoint Test A.
223
P0762
SSPC-C Intermed- iate Clutch
SSPC-C circuit, clutch or solenoid failure - ON.
SSPC-C circuit, clutch or solenoid failed in the ON position during operation resulting in HIGH pressure in the hydraulic circuit.
Only 3rd and 4th gear available.
GO to Pinpoint Test A.
224
P0763
a
SSPC-C Intermed- iate Clutch
SSPC-C solenoid circuit failure.
SSPC-C circuit failed to provide voltage drop across solenoid. Circuit failure or TCM driver failure.
Tow/Haul OFF:
-
Only 1st, 2nd and 3rd gears available.
Tow/Haul ON:
-
Only 4th and 5th gear available.
GO to Pinpoint Test A.
334
P0979
SSPC-C Intermed- iate Clutch
SSPC-C solenoid or circuit shorted to ground.
Voltage through SSPC-C solenoid circuit is checked. An error will be noted if tolerance is exceeded. Short to ground failure detected.
Tow/Haul OFF:
-
Only 3rd gear available.
Tow/Haul ON:
-
Only 4th gear available.
GO to Pinpoint Test A.
335
P0980
b
SSPC-C Intermed- iate Clutch
SSPC-C solenoid or circuit shorted to power.
Voltage through SSPC-C solenoid circuit is checked. An error will be noted if tolerance is exceeded. Short to power failure detected.
Tow/Haul OFF:
-
Only 1st and 2nd gear available.
Tow/Haul ON:
-
Only 5th gear available.
GO to Pinpoint Test A.
225
P0765
SSPC-D Direct Clutch
SSPC-D solenoid circuit open.
SSPC-D circuit failed to provide voltage drop across solenoid. Circuit open or TCM driver failure during on-board diagnostics.
Tow/Haul OFF:
-
Only 5th gear available.
Tow/Haul ON:
-
Only 6th gear available.
GO to Pinpoint Test A.
231
P0766
SSPC-D Direct Clutch
SSPC-D circuit, clutch or solenoid failure - OFF.
SSPC-D circuit, clutch or solenoid failed in the OFF position during operation resulting in HIGH pressure in the hydraulic circuit.
Tow/Haul OFF:
-
No 5th gear available.
Tow/Haul ON:
-
No 5th or 6th gears available.
GO to Pinpoint Test A.
232
P0767
SSPC-D Direct Clutch
SSPC-D circuit, clutch or solenoid failure - ON.
SSPC-D circuit, clutch or solenoid failed in the ON position during operation resulting in LOW pressure in the hydraulic circuit.
No 1st, 2nd, 3rd or 4th gears available.
GO to Pinpoint Test A.
233
P0768
SSPC-D Direct Clutch
SSPC-D solenoid circuit failure.
SSPC-D circuit failed to provide voltage drop across solenoid. Circuit failure or TCM driver failure.
Tow/Haul OFF:
-
Only 1st, 2nd and 5th gears available.
Tow/Haul ON:
-
Only 5th and 6th gear available.
GO to Pinpoint Test A.
342
P0982
b
SSPC-D Direct Clutch
SSPC-D solenoid or circuit shorted to ground.
Voltage through SSPC-D solenoid circuit is checked. An error will be noted if tolerance is exceeded. Short to ground failure detected.
Tow/Haul OFF:
-
Only 1st and 2nd gears available.
Tow/Haul ON:
-
Only 5th gear available.
GO to Pinpoint Test A.
343
P0983
b
SSPC-D Direct Clutch
SSPC-D solenoid or circuit shorted to power.
Voltage through SSPC-D solenoid circuit is checked. An error will be noted if tolerance is exceeded. Short to power failure detected.
Tow/Haul OFF:
-
Only 5th gear available.
Tow/Haul ON:
-
Only 6th gear available.
GO to Pinpoint Test A.
234
P0770
SSPC-E Low/ Reverse Clutch
SSPC-E solenoid circuit open.
SSPC-E circuit failed to provide voltage drop across solenoid. Circuit open or TCM drive failure during on-board diagnostics.
Tow/Haul OFF:
-
Only 1st and 2nd gears available.
Tow/Haul ON:
-
Only 5th gear available.
GO to Pinpoint Test A.
235
P0771
SSPC-E Low/ Reverse Clutch
SSPC-E circuit, clutch or solenoid failure - OFF.
SSPC-E circuit, clutch or solenoid failed in the ON position during operation resulting in LOW pressure in the hydraulic circuit.
Tow/Haul OFF:
-
No 1st gear available.
Tow/Haul ON:
-
No 1st or 2nd gears available.
GO to Pinpoint Test A.
241
P0772
SSPC-E Low/ Reverse Clutch
SSPC-E circuit, clutch or solenoid failure - ON.
SSPC-E circuit, clutch or solenoid failed in the OFF position during operation resulting in HIGH pressure in the hydraulic circuit.
Tow/Haul OFF:
-
Only 1st gear available.
Tow/Haul ON:
-
Only 1st or 2nd gears available.
GO to Pinpoint Test A.
242
P0773
SSPC-E Low/ Reverse Clutch
SSPC-E solenoid circuit failure.
SSPC-E circuit failed to provide voltage drop across solenoid. Circuit failure or TCM driver failure.
Tow/Haul OFF:
-
Only 1st and 2nd gears available.
Tow/Haul ON:
-
Only 5th gear available.
GO to Pinpoint Test A.
345
P0985
b
SSPC-E Low/ Reverse Clutch
SSPC-E solenoid or circuit shorted to ground.
Voltage through SSPC-E solenoid circuit is checked. An error will be noted if tolerance is exceeded. Short to ground failure detected.
Tow/Haul ON:
-
Only 5th gear available.
GO to Pinpoint Test A.
351
P0986
b
SSPC-E Low/ Reverse Clutch
SSPC-E solenoid or circuit shorted to power.
Voltage through SSPC-E solenoid circuit is checked. An error will be noted if tolerance is exceeded. Short to power failure detected.
Tow/Haul OFF:
-
Only 1st and 2nd gears available.
Tow/Haul ON:
-
Only 5th gear available.
GO to Pinpoint Test A.
243
P0791
Intermed- iate Shaft Speed Sensor
Insuff- icient input from intermed- iate shaft speed sensor.
TCM detected an insufficient signal from the intermediate shaft speed sensor during operation.
Harsh shifts or engagements, engine rpm higher or lower than expected. No 1st, 3rd or 5th gears.
GO to Pinpoint Test D.
244
P0793
Intermed- iate Shaft Speed Sensor
No input from intermed- iate shaft speed sensor.
TCM detected a loss of intermediate shaft speed sensor signal during operation.
Harsh shifts or engagements, engine rpm higher or lower than expected. No 1st, 3rd or 5th gears.
GO to Pinpoint Test D.
245
P0794
Intermed- iate Shaft Speed Sensor
Intermed- iate shaft speed sensor signal intermitt- ent.
TCM has detected an intermittent intermediate shaft speed sensor signal.
-
GO to Pinpoint Test D.
422
P1780
TCS Switch
TCS switch input incorrect per selected position.
TCS switch voltage incorrect.
No Tow/Haul feature when TCS switch is pressed during self-test.
RERUN on-board diagnostics and cycle switch. If concern is still present, REFER to
Automatic Transaxle/ Transmission External Controls.
a Output circuit check, generated only by electrical symptoms.
b May also generate by some other non-electrical transmission hardware system.